高温存储对Sn-Pb-Ni凸点界面金属间化合物生长的影响

倒装焊工艺由于具有信号处理速度快、封装密度高、可靠性高等特点，已广泛应用于高密度集成电路封装工艺中。高可靠倒装焊器件的互连焊点通常采用10Sn90Pb等高铅焊料，该焊料具有剪切强度高、可靠性高等优点，但其熔点高、回流工艺窗口窄等特性给封装工艺带来一定难度，此外该焊料在高温存储环境的可靠性有待进一步提高。本文采用Ni元素对10Sn90Pb焊料进行改性，研究高温存储下Sn-Pb-Ni体系凸点的力学性能以及金属间化合物（Intermetallic compound,IMC）的生长演变规律，以此评估Ni元素对10Sn90Pb凸点可靠性的影响。主要结果如下：适量添加Ni元素可以细化10Sn90Pb焊点界面处IMC晶粒，降低高温存储条件下的IMC生长速度，但在一定程度上会降低凸点的剪切强度。0.05%~0.1%含量的Ni元素添加对10Sn90Pb凸点综合性能提升较为显著。     

自动测试系统集中互连信号优化设计

基于对自动测试系统被测设备的信号种类及数量的分析,构建了被测对象测试信号数学模型,分析了不同测试模式下的测试资源需求情况,并从提高测试系统性价比这一基本原则出发,提出了自动测试系统硬件平台测试资源优化配置的理论计算方法,对自动测试系统的工程设计具有指导意义。     

水洞动态测力和流动显示一体化实验技术

研制能够用于低速水流中的三分量内式测力天平,结合氢气泡(或染色液)方法,在水洞(槽)中实现测力和流动显示实验同步进行的动态实验系统,克服了通常测力和流动显示分别在风洞和水洞中进行,实验条件不同给结果分析带来的困难。天平采用高精度位移传感器,避开传统的应变片技术应用于水中所遇到的技术困难。简易飞行器模型的静态和等速俯仰实验结果表明了测量系统的可靠性。     

接地体的冲击电阻的分析与计算

在分析雷电电磁脉冲、核电磁脉冲等电磁脉冲(EMP)对地面电子设备可能造成的损害,以及电磁脉冲感应电流在接地体中的散流特性的基础上,给出了简单接地体的冲击接地作用的度量参数和冲击接地电阻的计算方法,并举例求得一个接地体的冲击接地电阻,为实际工程提供理论依据。     

下颔式进气道实验研究

为了验证下颔式进气道 /前机身一体化设计方案的合理性及其进气道性能 ,对下颔式进气道 /前机身一体化设计方案进行了实验研究。测出了进气道总压恢复系数、畸变指数随流量系数、攻角、侧滑角的变化规律。结果表明 ,进气道性能较好 ,进气道 /发动机匹配良好。最后提出了下颔式进气道的进一步改进措施     

某型加力涡扇发动机特性的三层迭代模拟

基于发动机各种部件特性，应用总体匹配技术发展了混排涡扇发动机特性的数值模型，并针对某型涡扇发动机建立了相应的三层迭代模拟方法及相应的计算机程序，给出了该发动机在某一组合调节方案下的特性模拟结果，模拟结果与试验结果比较表明二者吻合较好。     

高速再入飞行器的制导与控制系统设计

 针对高速再入飞行器模型的快时变,强耦合,严重非线性的特点,采用反馈线性化方法,设计了自动驾驶仪;同时采用最优制导律设计与理想速度曲线相结合的方法,设计了能同时保证末端制导精度及速度方向、大小的制导律。最后,进行了六自由度仿真,结果表明 :设计的制导律及控制方案是合理、有效的,易于实现。     

某型发动机对畸变进气响应的流动耦合分析

建立了畸变进气下某型双轴发动机高压压气机，扩压器间流动耦合模型，完善了畸变进气对发动机稳定性影响模拟方法。数值模拟结果表明，考虑耦合影响给出的高压压气机出口静压畸变与其总压畸变不仅相位相反，而且随进口总压畸变强度变化而变化。据此所给出的高、低压压气机畸变响应和发动机推力响应特性也与进气道，发动机相容性理论相符合。     

A new dynamic pushback control method for reducing fuel-burn costs: Using predicted taxi-out time

Long departure-taxi-out time leads to significant airport surface congestion, fuel-burn costs, and excessive emissions of greenhouse gases. To reduce these undesirable effects, a Predicted taxi-out time-based Dynamic Pushback Control(PDPC) method is proposed. The implementation of this method requires two steps: first, the taxi-out times for aircraft are predicted by the leastsquares support-vector regression approach of which the parameters are optimized by an introduced improved Firefly algorithm. Then, a dynamic pushback control model equipped with a linear gate-hold penalty function is built, along with a proposed iterative taxiway queue-threshold optimization algorithm for solving the model. A case study with data obtained from Beijing International airport(PEK) is presented. The taxi-out time prediction model achieves predictive accuracy within 3 min and 5 min by 84.71% and 95.66%, respectively. The results of the proposed pushback method show that total operation cost and fuel-burn cost achieve a 14.0% and 21.1%reduction, respectively, as compared to the traditional K-control policy.(3) From the perspective of implementation, using PDPC policy can significantly reduce the queue length in taxiway and taxi-out time. The total operation cost and fuel-burn cost can be curtailed by 37.2% and 52.1%,respectively, as compared to the non-enforcement of any pushback control mechanism. These results show that the proposed pushback control model can reduce fuel-burn costs and airport surface congestion effectively.     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.